Caradco Windows and Doors Replacement Parts and Hardware

Part Number: 701 Our Bushing is Metal and has been modified to meet 85 degree rotation needed for older handle sets.You can order a new handle set which comes with a bushing kit that we still have in stock - Part # 852For handle set from 2004 and prior - See picture to match your handle set to correct bushing kitThis Bushing Kit is for Swinging Patio Doors Double Bore System ONLY.This will rebuild one interior or one exterior bushing.Two kits are needed to rebuild the complete door handle.For instructions on how to replace Bushing Kit please click on our Blog Link: Window Parts Center Blog Known Brands: W&F, Hurd, Jeldwen, Caradco, Peachtree known number stamped on some handles: pat no 4,671,089 Associated Parts Sold Sold Separately: W&F Interior and Exterior Replacement Handles W&F Door Handle Solid Shaft 870 - W&F Handle Extension

Read more less

Part Number 335 Balance Window Springs For Single and Double Hung windows. Replacement window springs used on many single hung and double hung windows with compression tilt jamb jamb liners. Each spring will come with a Clip as shown in picture. Clip is removable if you do not need it on your window.Due to the multiple sizes springs come in we do not stock springs. All springs are special order with a 1 - 2 week lead time. NO RETURNS for springs as they are special order/made to your order.Spring is 3/8" Diameter outside to outsideThe spring gauge or tension is as follows and is commonly associated with these color tips on the springs themselves: Red .041, Green .044, Yellow .047, Black .048, Purple .051To Order By Spring Length Inches : Measure from tip of Eyelet to tip of Eyelet on spring. (Eyelet is the round bent out part of the spring located at both ends).To know what color gauge and length to order: you will need to remove the springs from the jamb liner. Most Springs are color coded at one end with paint. Please watch both how to videos below that show how to remove the jamb liners from your window/reinstall and how to remove and replace the springs. You can also use the chart in the pictures as a guide on which gauge to order (chart is for Hurd Wood/clad windows) other brand windows lengths or gauge of the springs can vary. so ordering a longer spring than needed is recommended and you can cut it to the length you need.  You can also determine gauge of a springusing a spring wire gauge, pocket wire gauge, or a math formula: Spring wire gauge: Insert the gauge into the spring and count 20 coils. Then, look at the gauge markings to find the wire size. Pocket wire gauge: Match the coils on the spring to the correct wire size key in the gauge. Math formula: Count 20 coils of the spring and measure their length in inches. Then, divide the measurement by 20 to determine the wire size Pro Tip: If the Springs are old and maybe a little stretched out it is better to order springs longer then you need as you can cut the springs shorter if needed by using a pair of Wire Cutters or Cable Cutters. Then you can bend out the eyelet with pair of regular pliers and flat head screw driver. See demonstration video below.Lead Time: Due to the multiple sizes springs come in we do not stock springs. All springs are special order with a 1 - 2 week lead time. NO RETURNS for springs as they are special order/made to your order. Larger orders may have longer lead times. Please contact us with any questions.   Have been used on Hurd, BiltBest, Weather Sheild and Cradco windows and many other window brands.

Read more less

Part Number 152 EntryGard (EntryGuard) Dual Arm Operator 5 17/64" (inch) Style Handing:  Left Hand Right Hand View pictures and how to video below (2:40 min) to determine handing you need. Measurements in Chart (Scroll Thru Pictures for Chart):  "A" Measurement in Drawing is 5 17/64" Circled in red in chart "B" Measurement in Drawing is 4 7/16"  circled in red in chart The other arm sizes are available for "A" and "B" measurements which can be ordered using our links below using our factory drop ship part catalog website (scroll thru pictures to see arm option chart for part numbers and See how to video below on how to read the chart).  Styles Available : Link Offset Up  Link Offset Down   Note: Detached clips can be revered in the field to be on top of bottom of arm. 152 will all come as Clip on the top. Finish:  E-Gard Handle and Cover Sold Separately See part # 139 for handle and #166 cover, S1002 Cover or upgrade to #S1004 for nesting handle and cover.  Known Part Numbers: 20910, L30941, 40853, U.S. PAT. 4,241,541 - CAN. PAT. 350,432 - PAT. 1982 , 31538, 40754, 45179, 40753, 31538A, 20810A, 15-63-00-002 15-63-00-001, MONCSE953, R3-2256, 53-2255  Replacement Parts for: Hurd, Semco, Marvin, Cascade, Caradco, BiltBest, Norco Milgard, Sierra Pacific, Allsco (1980 to Dec. 1997), Monarch Old Series and more. Other Arm Sizes Links to Order (this is an update to our video below). Watch video to see how to read chart in pictures above to determine your A and B Measurements match part numbers on chart to links below: Click here to order: 36-181 Click here to order: 36-182 Click here to order: 36-183 Click here to order: 36-184 Click here to order: 36-186 Click here to order 36-185 Info on our parts catalog factory direct website Cut Sheet For EntryGard Dual Arm 15 Series 

Read more less

852 - Handle Set for 6" Center to Center Bore Colors: Bright Brass, Satin Nickel, Oil Rubbed Bronze*, Polished Chrome**, White** *Color AS IS: Oil Rubbed Bronze Type Finish (ORB). We will not accept returns on it for any reason for this finish. See finish note below. When you place your order for ORB you are agreeing to these terms for the ORB item. **Discontinued Colors: White and Polished Chrome. Once our stock is gone these colors will no longer be available  Fits 2 1/8" Crossbore on 6" and 6 3/32" bore Centers. Can also be used on doors with 1 3/4" Crossbore. The lockset includes removable posts.  2 3/8" Back Set Mounting Screw Holes 6 1/16" center to center Durable Finish Fits Right or Left Hand doors East to install with Phillips screwdriver Known to work on Weather Shield, and Hurd Swinging Patio doors and replacement for W&F handle set with 6" Center to Center Bores. Tools Required for Install: Philips Screwdriver and Slotted Screwdriver.  Detailed Installation Instructions Enclosed.  Keyed and Keyed Alike: Standard: All handle sets come random Keyed with 2 Keys. You can order as Keyed Alike for a small upcharge per handle.  For 2 or more handle sets you can  have all of the handle sets come keyed the same.  (Example if you order QTY 4 handle sets you will also need to add QTY 4 keyed alike to to your under found under accessory items)  Allow an addition 1-2 weeks for keyed alike handle sets to ship We CAN NOT rekey handle sets to any existing keys you the customer may have for your home, you the customer would need to hire a lock smith for that. Known to have been used on:  Replacement for Peachtree  Part # 06200031. and is a replacement handle set for Hurd, Jeldwen, Caradco "Hallmark Leverset", and replacement handle for 6" center to center bore handle  sets for Hurd, W&F Weather Sheild an more. Known Part Numbers: 1200, 12001-1, 1200-1, 40061999, PAT NO's 4,671,089 D295,829, 14421-WR.  Part # 06200031 *Finish Notice For Oil Rubbed Bronze Type:  Has NO manufacture warranty on finish wear.  This product is sold AS IS and we will not accept returns on it for any reason. **Warning** Do NOT use a power driven tool to attach the handle set face plate retaining screws...thread damage can result and is NOT considered a product defect. No returns will be accepted if when inspected product has thread damage and not in new condition.  NOTE! 852 only works for  6 inch center to center bore and 6 1/16 inch center to center mounting screw holes, 2 1/8" standard double double bore with latch and dead bolt (see video and pictures with dimensions). (If you have the W&F multipoint hardware with 6 inch center to center 1 7/8" or  2 1/8" multipoint bore  and screw holes are 5 3/16" center to center see part number: D300, D301, D302, D303, D304 or D305 )   *Additional Finish Manufacturer Warranty info:  Warranty is for original consumer/purchaser Proof of product purchase is required. for Bright Brass, Stain Nickel and White only have a 1 year manufacturer warranty. Warranty does not cover normal wear and discoloration of Finishes, damage caused by scratches or abrasions, or any product that has been improperly installed, abused, worn out, altered or used for a purpose other than that for which it was intended, or used within 10 miles from the sea coast or body of salt water, or in a manner inconsistent with any instructions regarding its use or recommended care and maintenance, or that has been exposed to solvents, chemicals, or other harsh environments or foreign substances including any airborne foreign substances.  Pricing subject to change - cannot retro active any pricing on previous orders or hold pricing for future orders.

Read more less

Part # 308 Clutch Shoe - Sold individually  Compression Tilt Double Hung Windows Measures 2-3/8" (or 2 13/32") x 1/2" x 15/32" Color: White  Used On: Biltbest, Hurd, WeatherSheild, Caradco and many other window brands.  Known Part Number: H 4036 Associated parts Sold separately:  Part Number 335 Balance Spring Part Number 307 Clutch Pin Pack

Read more less

Part Number: 139 3 1/2 inch with 11/32 Inch Spline Replacement 3" Window Roto Operator Crank Handle for Amesbury Truth with 11/32" Spline Operators Truth Handle - Roto - Replacement Parts for Awning and Casement Windows operators.Colors: Bronze, New Goldtone, White, Beige, Brass, Goldtone, Clay, Aluminum, Chestnut Bronze, Medium Bronze, Brushed copper Nickel, Off-White, Black, Cocoa Brown, Blue White (aka Bright White), Tuscan Bronze, Oil Rubbed Bronze, Off White (aka Euro white) Special Order Colors:  Special order colors or Pre-order colors are non returnable and can have up to a minimum 3 week lead time. Large QTY orders of 50 or more will also be considered special order none returnable. ** Please note: That the Short Handle Roto Crank has been discontinued by the manufacturer. Once our stock is depleted we will ship out the longer version of the Roto Crank Handle that will work on your windows. Known to have been used on many window Brands: Biltbest, Crestline, Caradco, Peachtree, Vetter, Oldach, Windsor, Sliver Line and Crank Handle standard Hurd used on  casement and awnings  manufactured pre February 1998.  Known Part Numbers: 139, 45054 31, HCSE29  

Read more less

Part Number 166 EntryGard Replacement Covers Only - 10341 Amesburty Truth  Truth EntryGard Operator Contour Cover Only - Fits 15 Series EntryGard Casement and Awning Operator andHandles 139 and 135 sold separately  - See Accessories items Known Part Numbers On Operator: 20910, L30941, 40853, U.S. PAT. 4,241,541 - CAN. PAT. 350,432 - PAT. 1982 , 31538, 40754, 45179 Discontinued Color:  Coppertone. For Additional Entrygard Covers in different styles  and colors see part numbers S1002 and S1004  Replacement Parts for: Hurd, Semco, Marvin, Cascade, Caradco, BiltBest, Milgard, Sierra Pacific and more. Free Economy Shipping On All USA Orders. If Cover color or QTY you want to order is is out of stock you can pre-order and parts will ship out as soon as they come in from the factory.

Read more less

Part Number: 105   Amesbury Truth 15 Series "Traditional Square Case 13 1/2"" has been replaced by the Ellipse Case 60 Series (13 1/2"). They are a Direct Replacement, only difference is the case design. See pictures for more details.  13 1/2 Inch Measurement is taken from center of housing to center of nylon roller - see drawing to measure accurately on your operator.  Known Part Number: 15.32, 105, 45251, 45136, U.S. PAT. 4505601, PAT. CANADA 1986, U.K. PAT. 2135397, 7707, 15-32-32-062, 15-32-32-061, HCSE43 Known Replacement Parts for: Hurd, Caradco, BiltBest, Oldach, Allsco, Semco (1976-1986) and more Associated Parts Sold Separately:  139 Handle Roto Crank - 3 1/2" with 11/32" Spline Operators with Similar Housing But Different Arms and Lengths:  Part Number S1082 - Truth/Wright Dyad Operator Part Number S1048 - Truth/Wright Dyad operator Part Number S1068 - Truth/Wright Dyad Operator Part Number 105 - Truth/Wright Straight Arm Part Number 115 - Truth/Wright Straight Arm Part Number 109 -Truth/Wright Straight Arm Part Number 112 - Truth/Wright Straight Arm Part Number S1037 -GU - Split Arm Dyad Operator Part Number S1038 GU - Split Arm Dyad Operator Kit Part Number 111 - Truth/Wright Split Arm Dyad Operator  

Read more less

Part Number: 520 Sliding Patio Door Panel Replacement Rollers - Steel Ball Bearing Sold Individually  (2 required per door)  5 3/4 inch long from Center of screw hole to center of screw hole 11/16" thickness 1 1/4 wheels  Style: Heavy duty for wood clad patio doors ( 1 roller weights 9.3 oz). Light duty for vinyl patio doors (1 roller weights 6.6 oz) Known Brands and Part#'s: 520, 012021, Hurd, Crestline, Park Vue, Merrill Millwork, Kolbe & Kolbe Millwork, Weather Shield, Semco and more.Known Part # 012021, PVS15, HWTR01 *Note to customer* there are a wide variety of rollers available. If the drawing does not look exactly like your tandem roller Click Here to see all rollers on our website. If you cant find the part you are looking for please email or text us a picture of your roller and our research team would be happy to assist you with finding the right one. Email: Info@WindowPartsCetner.com Text Line: 303-222-4489  

Read more less

Part Number: S1107 Amesbury Truth 16 Series HomeGard Casement Window Sash Lock Color: White and Bronze  (New Goldtone has been discontinued and once our stock is gone it will no longer be available) What's Included: Each lock is Sold complete with: 1 Lock, 1 Left Keeper, 1 Right keeper and color matching mounting screws for lock and keeper (so you can use on either left hand or right hand operating casement windows). Dimensions: 2 1/4 Inch Wide x 2 3/4" Tall x  3/8 Inch deep at 1st step and 15/16 inch deep at 2nd step Screw Hole Spacing: 2 5/16 Inch Center to Center  HomeGard Sash Locks are a perfect low-profile lock option for windows with smaller side stops. Featuring .625" pull-in, HomeGard locks offer a strong detent which consistently provides a more secure feel during lock up. HomeGard locks can withstand negative air pressure of 275 lbs. per lock. Known to have been used on: Crestline, Vetter and Peachtree Windows, Semco  Known part number stamped on back: 45428 Truth, Truth w/ House Symbol Replacement version for locks stamped with 21328A, Retro fit replacement option for lock with stamp on back of 31664  

Read more less

Part Number: 216 Crank Handle Adapter 5/8 Inch Hex Femail used with  Clear Story  Windows Size: Spline Size see list below 11/32 Spline Fits: Truth (Amesbury Truth): Marvin, Some Milgard, Caradco, Weather Shield, Hurd, BiltBest, Eagle, Vetter, Roto X Drive and Others 9/32 Spline Fits Peachtree and Getty 3/8 Special Spline Fits: Pella 3/8 Special Spline Fits: Anderson 3/8 Spline Fits: Some Milgard and Others Finish: Mill (Special order colors email for pricing: White, Black and Champagne)  Put those operable clerestory windows to energy-saving use with our 39-series clerestory extension crank. High mounted windows are excellent for capturing light while providing privacy, but they can also be “excellent” heat traps. It is now possible to vent the heat that rises to these areas as easily as opening any other window in the home.It’s inexpensive and can easily retrofit to existing or new window installations. By simple removal of the existing crank handle and replacement with an adapter (Hex-Bolt) the crank will open and close any operable clerestory window. It is not necessary to replace the current operator.The removable extension crank is available in many standard sizes for either sill or jamb mounted operators. (See Manual Window Wands) The standard finish for the crank is natural anodized aluminum.

Read more less