Hoppe

Part Number: 829 Hoppe Split Shaft only screws sold separately (See Part Number: 840-031 Set Screws or S3004 - metric 6-10) Shaft Size Order By Length:  3 15/16 inch ( 5/16 inch x 3 15/16 inch or 8 mm x 100 mm) For Doors Smaller 1 3/4 inch thick Can be used as a replacement split shaft for old GU handle sets 4 21/64 inch (5/16 inch x 4 21/64 inch or 8mm x 110 mm) For Doors Smaller than 1 3/8 inch thick 4 11/16 inch (5/16 inch x 4 11/16 inch or 8 mm x 120 mm) For 1 3/4 Thick Doors Commonly used on Hurd and Truth hardware 5 1/2 inch (5/16 inch x 5 1/2 inch or 8 mm x 140mm) For 2 1/4" thick doors 6 1/4 inch (5/16 inch x 6 1/4 inch or 8 mm x 160 mm) used with the 1" Hoppe Handle extension part # 828 sold separately Commonly used on Hurd and Truth hardware that has extension 828   See figure F in drawing for correct split shaft spindle position installation.  Associated Parts Sold Separately:  6 1/4 is used with the 1" Hoppe Handle extension part # 828 Part Number: 840-031 Set Screws pack  Part number S3004 - metric 6-10 screws

Read more less

#834 - Hoppe 3Pt Striker For Rollers - Auto - Bright Brass Replacement Parts for Hoppe Multipoint Hardware used on swinging patio doors Known To have Been Used On: Hurd, Weather Sheild, Hoppe, Marvin BiltBest and many other door brands that used Hoppe Multi Point Hardware  Sold Separately Are Part Numbers:  #813 - Hoppe 3Pt Convert Auto Release Striker #833 - Hoppe 3Pt Convertible Under plate    

Read more less

Part Number 810R  Hoppe Multipoint Automatic Roller Bottom Gear Box Extension HLS9000 CUSOTMER PLEASE READ BEFORE YOU ORDER: See chart for dimensions to compare with your multipoint BEFORE you place your order. If measurements do not match for your multipoint please email us for the worksheet you will need to fill out for a quote. Single point gearbox is not interchangeable with multipoint gearbox. The cover may look the same but internal components are different. Info@WindowPartsCenter.com Material: Stainless Steel (sliver). Brass color no longer manufactured - only comes in stainless steel for both the gear box and the extension. See features and benefits picture.  Style: Roller Comes with: bottom extension with gear box attached (top extension SOLD separately see part number 820R for top extension these are for Hurd doors only. For other brand doors please email for worksheet to fill out for a quote)  The Hoppe #810R/820R Roller style is the direct replacement for old FUHR Roller Multi point that was on Hurd – no modification is needed when changing to the Hoppe #810 - you need to order both top extension 820 and lower extension with great box 810 to use as a replacement with old FUHR. The only difference is some of the FUHR multi point had an automatic fire to engage the multi point, the Hoppe does not. So with the Hoppe to engage the multi point you close the door then lift up on the door handle then throw the dead bolt to lock. Handing: Non handed latch is reversible. See video on how to change latch handing  Associated Parts Sold Separately: 820R - Hoppe Multipoint Automatic Roller TOP Extension HLS9000 813 -  Hoppe 3Pt Convert Auto Release Striker  833 -  Hoppe 3Pt Convertible Under plate  834 - Hoppe 3Pt Striker For Rollers 819 - Hoppe Multipoint Latch Plate  S4019 - Hoppe LATCH AND DEADBOLT STRIKE WITH CURVED LIP S1400AC - Active with Cylinder Munchen Series M112PI/216N Handle Set S4300AC - Active with Cylinder Hoppe Munchen Series M112PI/3965N Handle Set S4200AC - Active with Cylinder Hoppe Munchen Series M112PI/374N Handle Set S4100AC - Active with Cylinder Hoppe Munchen Series M112PI/216N Other Hoppe Multipoint and Single Point We Stock: 810T - Hoppe Multipoint Automatic Tongue Lower Extension HLS9000 820T - Hoppe Multipoint Automatic Tongue TOP Extension HLS9000 825 - Hoppe Single point Gear Box For Hoppe Multipoint We Do Not Stock Please Email us for worksheet and quote  Install Instructions (also see instructions in pictures): Remove set screws on handle levers and remove remove three mounting screws on faceplate estuation  On side of door remove screw that lines up with the lock cylinder. Remove the handle set Remove all screws down the side of the door that holds on the multipoint system (keep all screws you will reuse them) Install new multipoint with screws Test for Operation  Reinstall handle set Test for proper operation 810R Known to have been used on: For Classic Hurd Doors Manufactured from 2005 and Prior. Fuhr Multi point used on Classic Hurd doors are no longer manufactured - Hoppe Multi point is the direct replacement. Number Known To Have Been On Older Gear Box (Hoppe Roller Style Brass Color): 1334291 - this is a component number. 

Read more less

Part Number S4104 Hoppe CES Ring Wrench Tool For Plastic Insert Cylinder with Crescent Knob To convert cylinder from 90 degree to 360 degree - see pictures for instructions  Special order item no returns. Please expect a lead time of 1-4 weeks.  Related Parts Sold Separately: Part Number S4105 - 2mm or 5/64" Hex Wrench Part Number S4106 - Plastic Insert Part Number S4107 - Set Screw

Read more less

Part Number 827 - SOLD Individually  Hoppe Backplate Bushing  -  (handle set or other parts not included) This Hoppe Backplate Bushing is for Hoppe Swinging Patio Doors System ONLY. Color: Clear Gold Opaque  HANDLE BUSHING HFW F12 BACKPLATE MANUFACTURER: A/35/14 914 RL 750 16S 85 Used on Hurd handle set from 2004 and prior - See picture to match your handle set to correct bushing kit for Hurd DoorsThis Hoppe Backplate Bushing is for Swinging Patio Doors System ONLY.  

Read more less

Part Number: 1001  Hoppe French Casement Hardware Handle 38MM (1.5 inch) Shaft Part Number 1001 has been known to have been used on Hurd, Sierra Pacific, Marvin and more French Casement Windows. Replacement option for old FUHR hardware that was bought out by Hoppe Color In stock  White is the only color we stock.  ( #37 White, Brushed Chrome, Champagne, Satin Taupe, Matte Black  is no longer available)  All other colors are Special Order items: Rustic Umber - also called Oil Rubbed Bronze FB by Hurd and Sierra Pacific. FB finish which means means its a stable finish and NOT a living finish that will change over time.  Antique Finishes from HOPPE North America deliver the unique aesthetic of an aged finish for the discerning hardware connoisseur. Intended to simulate the natural and inconsistent qualities that come with tarnish and age, Antique Brass and Antique Nickel finishes are the result of carefully handcrafted process that have been thoroughly refined. Antique Brass and Antique Nickel finishes by HOPPE will maintain their original appearance and are not considered “living” finishes. These finishes feature coatings that protect each surface from tarnish.  When considering Antique Finishes, the user should be aware these finishes will exhibit variation in color and shade just as an actual tarnished piece of brass or nickel would show. Curved and shaped surfaces will show greater contrast and highlights of golden brass or shiny nickel as shown above. Slight variations can also be expected from one piece to the next. HOPPE maintains a careful balance of consistency blended with purposeful variation to yield the desirable aesthetic of an Antique Finish. The result is a unique hardware piece created with an artisan’s touch. If more consistent appearance is desired, HOPPE recommends Polished Brass (F71, F77-R) in place of Antique Brass and Satin Nickel (F42, F42-R) in place of Antique Nickel. All other colors are special order items NO returns, exchanges or cancellations. We DO NOT stock them. Customers please expect  a 3-6 week lead time All color finishes  are very nice and that is why the price is so much more (except for the #37 White as already noted)  Related Parts Sold Separately:  Part Number 1000 - French Casement Connector Shaft FC Adaptor Part Number 1001 - French Casement Handle 33MM (1.5") Shaft  Part Number 1002 - French Casement Mounting Plate Part Number 1003 - French Corner Drive VS S-ES A0055 Part Number 1004 - French Casement Eurogroove Cover, Long Part Number 1005 -  French Casement Eurogroove Cover, Short Part Number 1006 - French Casement Gear S-ES 115/16 2MV FH Part Number 1007 - French Casement FC Linkage Part Number 1008 - French Casement Strike Lead-In S-ES Part Number 1009 - French Casement Strike

Read more less

Part Number: S4011 - SET Hinge Hoppe Adjustable Door Hinge Non Removable Hinge - Set Hinge Vertical Adjustment  S4011 is Vertical Adjustment ONLY Watch video and read instructions in pictures (For Horizontal adjustment see part number S4012 Sold Separately and see hinge placement guide in picture) No Screws Included, sold individually  Handing: Left Hand Hinge Used For: Left Hand In swinging (LHI) or Right Hand Out Swinging (RHO) Right Hand Hinge Used For: Right Hand In Swinging (RHI) Left Hand Out Swinging (LHO) SEE  Hoppe "Application Diagram for Set Hinge” TO DETERMINE WHAT HANDING HINGE TO ORDER Pre-Order are Special order items, no returns  Made out of Brass or Aluminum. Multiple finishes to choose from.  Designed for a Greater Advantage • Adjusts vertically ( Use Set Hinge Part # S4011) and  for horizontally ( see Guide Hinge Part # S4012) by 1/8" for a perfect swing. - see Installation Instructions page 1 number of hinges chart for application. • Brass hinges feature finial caps as shown • Aluminum hinges feature flush caps. • Large 3/16" hex head screws make adjustments effortless. Remove the finial in the set hinge to access the hex screw. • Single pass routing for quick and easy installation. • All Set and Guide Hinges are equipped with non-removable pins for security, making HOPPE Adjustable Hinges the ideal solution for both inswing and outswing doors. • Especially designed for larger doors, with a panel weight capacity of up to 330 lbs. Tested to a Higher Standard • Brass hinges are tested beyond an impressive 2.5 million cycles, in accordance with ANSI A156.1 Grade 1 – Commercial test procedures. • Backed by HOPPE's Limited Lifetime Mechanical Warranty. Finished with Superior Quality HOPPE's Brass and Aluminum Hinges are outstanding corrosion resistant materials HOPPE uses their Resista® Limited Lifetime Finish Warranty on four of their select premium finishes. The Aluminum Hinges have a high quality powder coating finish.  Installation Set and Guide Hinge Placement: 3 Hinges Per Door Panel Up to 165 lbs: Starting at top of door Top of door Guide (Use Part# S4012) Set (Use Part# S4011) Guide (Use Part# S4012) 4 Hinges Per Door Panel Up To 165 lbs: Starting at top of door Top of door Guide (Use Part # S4012)  Guide (Use Part # S4012)  Set (Use Part# S4011) Guide (Use Part # S4012) 4 Hinge Per Door Panel 165-330 lbs Starting at top of door Top of door Guide (Use Part # S4012)   Set (Use Part# S4011)  Set (Use Part# S4011) Guide (Use Part # S4012) 5 Hinges Per Door Panel Up To 165-330 lbs: Starting at top of door Top of door Guide (Use Part # S4012)  Guide (Use Part # S4012) Set (Use Part# S4011)  Set (Use Part# S4011) Guide (Use Part # S4012)  The Set hinge no matter what is always the 2nd from the bottom Pro Tip: Remove weight from the hinges by lifting up on the door before you adjust.  Known to have been used on: Sierra Pacific Doors, Ashworth and many other

Read more less

Part Number: S4014 S4014 Hoppe Millennium Adjustable Hinge - 2-D Guide Hinge with Non-removable Pin Horizontal Adjustment  - Hinges are Non Handed. Works for both Left hand and Right hand swinging doors. Known to been used on WeatherSheild and Peachtree Doors Colors Still Available: Stainless Steel  Discontinued Colors: Oil Rubbed Bronze, Antique Brass, Brass, Brushed Chrome Pat.Nr. 5.701.636 122190600, 850-8754743 Set and Guide Hinge Placement: 3 Hinges Per Door Panel - Up to 165 lbs: Starting at top of door Top of door Guide - Part Number S4014 Set - See Part Number S4013 Guide - Part Number S4014 4 Hinges Per Door Panel -Up to 165 lbs: Anytime you need 4 hinges you would just add another guide hinge Starting at top of door Top of door Guide - Part Number S4014 Guide - Part Number S4014 Set - See Part Number S4013 Guide - Part Number S4014 4 Hinges Per Door Panel - 165 - 330 lbs: Starting at top of door Top of door Guide - Part Number S4014 Set - See Part Number S4013 Set - See Part Number S4013 Guide - Part Number S4014 5 Hinges Per Door Panel - 165 to 330 lbs: Guide - Part Number S4014 Guide - Part Number S4014 Set - See Part Number S4013 Set - See Part Number S4013 Guide - Part Number S4014 Pro Tip: Remove weight from the hinges by lifting up on the door before you adjust.  Known part # 850-8754731, 850-8754743,122190600  General HOPPE Adjustable Hinge Adjustment Instructions: Determine hinge locations on the frame and door panel. Recommended hinge positions are given in the Set and Guide Hinge Placement Table above. Prepare the door panel and frame. Fasten hinges into the door panel. #10 ANSI wood screws with a minimum length of 1 1/4” are recommended. The Set Hinge must be installed according to the installation label. The label on the frame leaf will point down to the sill when properly installed. On the frame, use #10 ANSI wood screws that are 5/8” to 3/4” long in three of the four screw locations. One screw on each hinge should be at least 1 1/2” long to reach the stud. This screw is typically left out and is installed after the door is positioned in the rough opening. Install the frame leaf of the Set Hinge into the routing on the frame and fasten securely. Do not allow the Set Hinge(s) to support the weight of the panel without installing the Guide Hinges. Install the frame leaf of the Guide Hinges into the routings on the frame and fasten securely. Leaves on the Guide Hinges will slide freely up and down for alignment with the rout. Do not adjust hinges prior to the final installation into the rough opening. This will affect the ability of the door installer and end user to utilize the full adjustment range of the HOPPE Adjustable Hinge. Disassembly Do not attempt to remove the hinge pin, as this may cause damage. To disassemble the door panel from the frame, support the weight of the panel to relieve the weight from the hinges. Carefully remove either the frame leaf screws or door leaf screws to displace the panel. Adjustment Instructions Introduction There are two types of HOPPE Adjustable Hinges on each door panel: Set Hinge: One or two per panel. The Set Hinge provides ± 1/8” vertical adjustment. Guide Hinge: Two or three per panel. The Guide Hinges provide ± 1/8” horizontal adjustment. Look for the visible adjusting screw on the door sash leaf. This identifies the hinge as a Guide Hinge. Hinge designs may vary, but adjustment remains the same. Required Tools A 3/16” hex wrench is required. A small flat head screwdriver is required. A plastic putty knife is recommended. Vertical Adjustment for Doors with One Set Hinge With the door closed or open: Remove the press-fit Finial Cap from the bottom of the Set Hinge to expose the adjustment screw. Use the small screwdriver for Set Hinges featuring a plastic Finial Cap. A plastic putty knife is recommended for Set Hinges featuring a brass Finial Cap. Insert the hex wrench into the bottom of the Set Hinge. Tighten the screw to raise the panel and loosen to lower the panel. Reinstall the Finial Cap removed in Step 1. Vertical Adjustment for Doors with Two Set Hinges With the door closed or open: Remove the press-fit Finial Cap from the bottom of the Set Hinge to expose the adjustment screw. Use the small screwdriver for Set Hinges featuring a plastic Finial Cap. A plastic putty knife is recommended for Set Hinges featuring a brass Finial Cap. To raise the panel, insert the hex wrench into the top-most Set Hinge and tighten the adjustment screw to achieve the desired Insert the hex wrench into the other Set Hinge and tighten the adjustment screw 1/8 turn past the onset of resistance to distribute the panel weight evenly between both Set Hinges. To lower the panel, insert the hex wrench into the top-most Set Hinge and loosen the adjustment screw as far as possible without Insert the hex wrench into the other Set Hinge and loosen the adjustment screw to achieve the desired adjustment. Retighten the adjustment screw on the top-most 1/8 turn past the onset of resistance to distribute the panel weight evenly between both Set Hinges. Reinstall the Finial Caps removed in Step 1. Horizontal Adjustment With the door open: Insert a 3/16” hex wrench into the horizontal adjustment screw. Turn clockwise to decrease the margin and counterclockwise to increase the margin on the hinge side.

Read more less

Part Number:  S4012 – Guide Hinge Hoppe Adjustable Hinge - Guide Hinge - Non Removable Pin Style. S4012 is Horizontal Adjustment Only (Watch video and read instructions in picture's) No Screws Included, sold individually  GUIDE HINGES ARE NOT HANDED. Will work on both LH and RH Doors by how you mount the hinge If not in stock - Pre Order - Special order item - no return 3-8 week lead time  Made out of Brass or Aluminum. Multiple finishes to choose from.  Designed for a Greater Advantage • To Adjust vertically (Use Set Hinge Part # S4011) and  for horizontally (Use Guide Hinge Part # S4012) by 1/8" for a perfect swing. See Installation Set and Guide Hinge Placement • Brass hinges feature finial caps as shown • Aluminum hinges feature flush caps. • Large 3/16" hex head screws make adjustments effortless. Remove the finial in the set hinge to access the hex screw. • Single pass routing for quick and easy installation. • All Set and Guide Hinges are equipped with non-removable pins for security, making HOPPE Adjustable Hinges the ideal solution for both inswing and outswing doors. • Especially designed for larger doors, with a panel weight capacity of up to 330 lbs. Tested to a Higher Standard • Brass hinges are tested beyond an impressive 2.5 million cycles, in accordance with ANSI A156.1 Grade 1 – Commercial test procedures. • Backed by HOPPE's Limited Lifetime Mechanical Warranty. Finished with Superior Quality HOPPE's Brass and Aluminum Hinges are outstanding corrosion resistant materials HOPPE uses their Resista® Limited Lifetime Finish Warranty on four of their select premium finishes. The Aluminum Hinges have a high quality powder coating finish. Installation Set and Guide Hinge Placement: 3 Hinges Per Door Panel Up to 165 lbs: Starting at top of door Top of door Guide (Use Part# S4012) Set (Use Part# S4011) Guide (Use Part# S4012) 4 Hinges Per Door Panel Up To 165 lbs: Starting at top of door Top of door Guide (Use Part # S4012)  Guide (Use Part # S4012)  Set (Use Part# S4011) Guide (Use Part # S4012) 4 Hinge Per Door Panel 165-330 lbs Starting at top of door Top of door Guide (Use Part # S4012)   Set (Use Part# S4011)  Set (Use Part# S4011) Guide (Use Part # S4012) 5 Hinges Per Door Panel Up To 165-330 lbs: Starting at top of door Top of door Guide (Use Part # S4012)  Guide (Use Part # S4012) Set (Use Part# S4011)  Set (Use Part# S4011) Guide (Use Part # S4012)  The Set hinge no matter what is always the 2nd from the bottom Pro Tip: Remove weight from the hinges by lifting up on the door before you adjust.  Known to have been used on Sierra Pacific Doors and Ashworth

Read more less

Part Number 820R  Hoppe Multipoint Automatic Roller Top Extension HLS9000 for HURD DOORS ONLY CUSOTMER PLEASE READ BEFORE YOU ORDER: See chart for dimensions to compare with your multipoint BEFORE you place your order. If measurements do not match for your multipoint please email us for the worksheet you will need to fill out for a quote. Single point gearbox is not interchangeable with multipoint gearbox. The cover may look the same but internal components are different.  Material: Stainless Steel (sliver). Brass color no longer manufactured - only comes in stainless steel for both the gear box and the extension. See features and benefits picture.  Style: Roller Top Extension ONLY Size we stock: (see chart for full details and measurements):  6-8 = Top Extension Length 1019mm / 40.11in Retro = Top Extension Length 1031mm / 40.59in 6-10 = Top Extension Length 1078mm / 42.44in 8-0 = Top Extension Length 1407mm / 55.39in Comes with: Top extension ONLY (Bottom Extension with Gearbox SOLD separately see part number 810R for bottom extension with gear box)  The Hoppe #810R/820R Roller style is the direct replacement for old FUHR Roller Multi point that was on Hurd and other door manufactures – no modification is needed when changing to the Hoppe #810 - you need to order both top extension 820 and lower extension with great box 810 to use as a replacement with old FUHR. The only difference is some of the FUHR multi point had an automatic fire to engage the multi point, the Hoppe does not. So with the Hoppe to engage the multi point you close the door then lift up on the door handle then throw the dead bolt to lock. Associated Parts Sold Separately: 810R - Hoppe Multipoint Automatic Roller Lower Gearbox with Extension HLS9000 813 -  Hoppe 3Pt Convert Auto Release Striker  833 -  Hoppe 3Pt Convertible Under plate  834 - Hoppe 3Pt Striker For Rollers 819 - Hoppe Multipoint Latch Plate  S4019 - Hoppe LATCH AND DEADBOLT STRIKE WITH CURVED LIP S1400AC - Active with Cylinder Munchen Series M112PI/216N Handle Set S4300AC - Active with Cylinder Hoppe Munchen Series M112PI/3965N Handle Set S4200AC - Active with Cylinder Hoppe Munchen Series M112PI/374N Handle Set S4100AC - Active with Cylinder Hoppe Munchen Series M112PI/216N Other Hoppe Multipoint and Single Point We Stock: 810T - Hoppe Multipoint Automatic Tongue Lower Extension HLS9000 820T - Hoppe Multipoint Automatic Tongue TOP Extension HLS9000 825 - Hoppe Single point Gear Box For Hoppe Multipoint We Do Not Stock Please Email us for worksheet and quote  Install Instructions (also see instructions in pictures): Remove set screws on handle levers and remove remove three mounting screws on faceplate estuation  On side of door remove screw that lines up with the lock cylinder. Remove the handle set Remove all screws down the side of the door that holds on the multipoint system (keep all screws you will reuse them) Install new multipoint with screws Test for Operation  Reinstall handle set Test for proper operation 810R/820R Known to have been used on: For Classic Hurd Doors Manufactured from 2005 and Prior. Fuhr Multi point used on Classic Hurd doors are no longer manufactured - Hoppe Multi point is the direct replacement. Number Known To Have Been On Older Gear Box (Hoppe Roller Style Brass Color): 1334291 - this is a component number. 

Read more less

Part Number S4102 Hoppe 90 Degree Profile Full Cylinder with Crescent Knob For 1 3/4 Inch to 2 1/2 Inch Thick Door Panel Can be converted from 90 degree to 360 degree - see pictures for instructions and videos below. Cylinder Sizing: Verify Door Thickness and Cylinder size by using chart "Inside Distance A" and "Outside Distance B" according to door thickness, Euro groove location and the style of back plate used.  Sizing:   For Doors: 1 3/4 Inch to 2 1/2 Inch Thick Door Panel See chart  For Doors: 2 1/8 inch to 3 inch Doors - see chart  Related Parts Sold Separately: Part Number S4103 - Hoppe Short Cylinder Insert Part Number S4105 - 2mm or 5/64" Hex Wrench Part Number S4107 - Set Screw For 2 1/8 inch to 3 Inch Thick door panel Full Cylinder  see part number  Trouble shooting:  If you cannot get the cylinder to line up and go in you need to lower the pin beneath the thumb turn. That frees the cylinder to move and line up for install. Then once put in and turned the cylinder will operate. It is a newer safety feature on these cylinders. Please watch video below.  

Read more less